# Neue Publikationen in Ziel-Venues – 2026-11-18 Neue Werke: 3 · davon mit DE-Affiliation: 3 Venues: 60 · abgefragt ab publication_date 2026-10-19 · letzter Lauf: 2026-11-18T18:13:50 ## Applied Physics Letters (APL) — 1 neu · _materials_ ### Broadband optical readout based on S 11 reflection-valley modulation in an AlN film bulk acoustic resonator ⚑ DE - **DOI:** [10.1063/5.0353007](https://doi.org/10.1063/5.0353007) - **Metadaten:** Erschienen: 2026-11-16 · Vol. 129, Issue 20 · OpenAlex seit 2026-11-18 - **DE-Institutionen:** Institute for Advanced Study - **Autoren:** - Kexin Miao — University of Electronic Science and Technology of China (CN) - Yuanhang Qu — Wuhan University (CN) - Lei Liu — Wuhan Textile University (CN) - Chengxiao Mo — Wuhan Textile University (CN) - Gaohui Ge — University of Electronic Science and Technology of China (CN) - Yan Liu — Wuhan Textile University (CN) - Tao Zhao — University of Electronic Science and Technology of China (CN); Institute for Advanced Study (DE) - Hao Xu — University of Electronic Science and Technology of China (CN) - **Topics:** Acoustic Wave Resonator Technologies; Mechanical and Optical Resonators; Ultrasonics and Acoustic Wave Propagation - **Abstract:** Here, we demonstrate a broadband optical readout strategy based on S11 reflection-valley modulation in an AlN film bulk acoustic resonator. Under optical illumination, the reflection valley progressively deepens and narrows with increasing optical power, corresponding to an increased loaded Q factor, while the resonance frequency changes only slightly. At a representative wavelength of 980 nm, the reflection-valley amplitude exhibits an approximately linear dependence on optical power density, with a responsivity of −57.95 dB/(mW/mm2). Similar amplitude modulation is observed over the measured wavelength range from 405 to 980 nm, demonstrating the broadband nature of the proposed readout. To clarify the electrical-port basis of this response, the measured S11 spectra are converted into the input impedance and admittance. The real part of the input admittance increases systematically with optical power density, whereas the imaginary part varies only weakly, indicating that the illumination-induced electrical-port modification is predominantly conductance-related. Layer-resolved optical simulations further show that the optical energy deposition occurs mainly near the top Mo electrode, while thermal simulations and reference-heating measurements indicate that significant global photothermal heating is unlikely to dominate the observed modulation. Modified Butterworth–Van Dyke analysis further reveals concurrent decreases in the effective static-branch resistance R0 and motional resistance Rm, providing an equivalent-circuit description consistent with the directly observed conductance enhancement. These results establish S11 reflection-valley modulation as a broadband amplitude-domain electrical-port optical readout strategy complementary to conventional frequency-shift-based resonant optical sensing. ## Sensors (SENSORS) — 2 neu · _materials_ ### A Fully Circular P+/N-Well CMOS Diode with Low Dark Count Rate for Single-Photon Imaging ⚑ DE - **DOI:** [10.3390/s26227226](https://doi.org/10.3390/s26227226) - **Metadaten:** Erschienen: 2026-11-16 · Vol. 26, Issue 22, S. 7226 · OpenAlex seit 2026-11-18 - **DE-Institutionen:** University of Siegen - **Autoren:** - Soumya Shatakshi Panda — University of Siegen (DE); KIIT University (IN) - Zidu Li — University of Siegen (DE) - Moin Diwan — University of Siegen (DE) - Paul C.-P. Chao — National Yang Ming Chiao Tung University (TW) - Bhaskar Choubey — University of Siegen (DE) - **Topics:** Advanced Optical Sensing Technologies; Advanced Semiconductor Detectors and Materials; Particle Detector Development and Performance - **Abstract:** We present a fully circular p+/n-well Single-Photon Avalanche Diode (SPAD) with a 10 µm active area diameter. A lightly doped p-well region surrounds the active region to prevent any premature lateral periphery breakdown. Fabricated using a 0.18 µm UMC Complementary Metal-Oxide-Semiconductor (CMOS) process without any additional customized layers, the diode demonstrates a low dark count rate (DCR) of 24.7 cps/µm2 at room temperature and a peak photon detection probability (PDP) of 16% at a wavelength of 620 nm with a 0.7 V excess bias voltage. Additionally, using dedicated front-end pixel circuit, the single-photon avalanche diode achieves a low after-pulsing probability of 0.45% and a timing jitter of 92 ps at the same excess bias voltage, validating the hypothesis of improved performance from diodes fabricated without corners. ### From Classroom Requirements to Validated Measurement Hard-Ware: Enabling AR-Supported Classroom Experimentation in Electrodynamics ⚑ DE - **DOI:** [10.3390/s26227217](https://doi.org/10.3390/s26227217) - **Metadaten:** Erschienen: 2026-11-16 · Vol. 26, Issue 22, S. 7217 · OpenAlex seit 2026-11-18 - **DE-Institutionen:** Ludwig-Maximilians-Universität München - **Autoren:** - Christoph Hoyer — Ludwig-Maximilians-Universität München (DE) - Max Warkentin — Ludwig-Maximilians-Universität München (DE) - Atakan Çoban — Ludwig-Maximilians-Universität München (DE) - Zoya Kozlova — Ludwig-Maximilians-Universität München (DE) - Tobias Schnaitmann — Ludwig-Maximilians-Universität München (DE) - Jochen Kühn — Ludwig-Maximilians-Universität München (DE) - **Topics:** Augmented Reality Applications; Experimental and Theoretical Physics Studies; Science Education and Pedagogy - **Abstract:** This article presents the requirements-driven development and multilevel validation of measurement hardware for augmented reality (AR)-supported experimentation in electrodynamics, using the Lorentz force as an application case. Based on functional design and quantitative measurement performance requirements, three research questions were formulated addressing the metrological, functional, and educational validity of the system. To meet the derived requirements, current and millinewton-scale force measurement as well as conductor position tracking were integrated into a compact, self-contained experimental setup which continuously transmits measurement values through a device-independent Bluetooth Low-Energy interface. Metrological validation demonstrated high linearity, good accuracy and repeatability for current and millinewton-scale force measurements, meeting the requirements derived for classroom investigations. Functional validation confirmed the theoretically expected linear relationship between electric current and Lorentz force. An exploratory educational validation with 92 secondary school students showed no hardware-related failures. After adjustment for pretest conceptual knowledge, learning outcome scores were higher in the spatially integrated AR condition than in the screen-based control condition. This difference was statistically significant in the planned directional test. Overall, the results demonstrate how classroom requirements can be translated into validated measurement hardware for innovative AR-supported learning environments connecting real experimentation with representations of otherwise non-observable quantities and complex models.